How to clean a glass bong - Budder Bongs
Smoking in a sparkling bong is a common pastime of glass bong enthusiasts. However, the majority of them are hesitant to clean their filthy bongs. Cleaning a bong is not difficult, and there are a few basic steps to follow.

HOW TO CLEAN THE OUTSIDE OF A BONG

You'll need a microfiber cleaning cloth and vinegar to clean the outside of a bong, preferably distilled vinegar (or lemon juice if you don't have vinegar) since it has a milder vinegar scent. You dampen a cleaning cloth with vinegar and wipe the surface of your water bong. Fingerprints and water stains are usually easy to remove. You should try this cleaning method right now because it is easy.


HOW TO CLEAN THE INSIDE OF A BONG

You'll need the following items to clean a glass bong or dab rig.

  • Cotton balls,
  • salt
  • isopropyl alcohol
  • Hand towels made from Q-tips or toothbrushes
  • Tupperware pots
  • tiny Ziploc packs
  • hot water

STEP 1- GET RID OF THE DIRTY BONG WATER

A pungent odour emanates from the polluted water from a bong. So, before you do anything else, make sure you empty it. Since the liquid in the filthy bong water is poisonous, make sure it does not come into contact with your body while draining it.

STEP 2- TAKE YOUR BONG APART

To prevent breakage, remove the bong bowl and stem from the glass bong. Since bongs are generally made up of many detachable glass bits, it's essential to disassemble the entire bong before cleaning it.

STEP 3- CLEAN ALL THE PIECES WITH HOT WATER

Begin cleaning the various disconnected parts while maintaining a steady stream of hot water to aid in the removal of sticky dirt that refuses to leave your water bong. Warm water is fine, but hot water removes the oils from herbs more effectively. If you intend to use boiling water, be cautious not to burn yourself.

STEP 4- PLACE EVERY LOOSE PIECE IN ITS CONTAINER

To keep track of where each piece is, put them in separate containers. After that, clean the pieces with an alcohol and salt solution as a detergent.

STEP 5- SHAKE

After adding a tablespoon of salt and alcohol to the sealed Tupperware case, give it a good shake. The salt and isopropyl alcohol penetrate even the tiniest gaps to eliminate the sticky residue left behind by excessive marijuana smoking. If you shake the rubbing alcohol and coarse salt together quickly, it will work quickly. If you think it'll become more involved, add more alcohol and salt; bear in mind that the dirtier your parts are, the more alcohol and salt you'll need.

After quickly shaking the pieces clean, put them somewhere secure before moving on to the next move.

STEP 6- ADD SALT AND ALCOHOL INTO YOUR BONG

The more salt and alcohol you use, the bigger the bong gets. The salt and alcohol are used to make the solution extremely corrosive and reliable. Cleaning your bong will depend heavily on accurate salt and rubbing alcohol measurements.

STEP 7- COVER ALL THE OPEN SPOTS AND SHAKE CONTINUOUSLY

 The more salt and alcohol you use, the better the bong gets. The salt and alcohol are used to make the solution extremely corrosive and reliable. Cleaning your bong will depend heavily on accurate salt and rubbing alcohol ratios. 

STEP 8- RINSE ALL THE TOOLS USING HOT WATER

Clear the bong of all alcohol and salt, then remove the small bits from the Tupperware container after continuous shaking. To clean the bong and the small parts properly, you'll need a steady stream of hot water.

Then, to dilute the isopropyl alcohol, salt, and sticky residue, rinse your bong with hot water. Remove any remaining dirt with a Q-tip or toothbrush. After that, leave the bits to dry out in the open air. If your glass bongs have water stains inside after drying, you can remove the stains with vinegar and a rag. Your bong now looks brand new!

Leave a comment

All comments are moderated before being published